features: wide operating temperature (-40c to 85c) stable threshold current for easy transmitter control (t 0 ~ 80k) 1310 nm typical emission wavelength fp-lds pigtailed package high-speed modulation capability (up to 5gb/s) excellent reliability ? ultra-low gradual wear-out rates ? <1% failures in 20 yrs at 55c application source for high-speed data-communication and telecommunication links ? sonet, fiber-channel, giag-bit ethernet, fttx ? catv / satellite and other analogue markets 1310 nm fabry-perot (fp) laser diode pigtailed package fp-1310-5i-xxx preliminary data sheet the fp-1310-5i-xxx is an mocvd grown inalgaas ridge laser diode with emission wave-length of 1310 nm and standard continuous light output of 5 mw per facet. these lasers provide stable, single transverse mode oscillation. these are hermetically sealed devices with an integrated monitor photodiode to monitor the optical output. the to-56 laser can is mounted inside a metal coaxial package which is then pigtailed with a singlemode fiber and terminated with a fiber connector. the pigtail comes in a choice of 50cm or 100cm lengths as standard, terminated with either fc or sc connectors with an apc or upc polish. suitable as a light source for data-com and telecom applications with data rates up to 5 gb/s. part number description fp-1310-5i-50smf-fcupc 1310 nm fabry-perot (fp) laser diode, 50cm singlemode pigtailed package, fc upc connector. fp-1310-5i-50smf-fcapc 1310 nm fabry-perot (fp) laser diode, 50cm singlemode pigtailed package, fc apc connector. fp-1310-5i- 100smf-scupc 1310 nm fabry-perot (fp) laser diode, 100cm singlemode pigtailed package, sc upc connector. fp-1310-5i- 100smf-scapc 1310 nm fabry-perot (fp) laser diode, 100cm singlemode pigtailed package, sc apc connector. . other fiber lengths and connector options available on request.
fp-1310-5i-xxx 1310 nm fabry-perot (fp) laser diode notice: stresses greater than those listed under ?absolute maximum ratings? may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operations section for extended periods of time may affect reliability. notice: the inherent design of this component causes it to be sensitive to electrostatic discharge (esd). to prevent esd-induced damage and/or degradation to equipment, take normal esd precautions when handling this product absolute maximum ratings symbol parameter conditions rating unit p o output power cw 10 mw v r ld reverse voltage (laser diode) - 2 v v r pd reverse voltage (monitor photodiode) - 10 v i f pd forward current (photodiode) - 1 ma t c operation temperature - -40 to + 85 c t stg storage temperature - -40 to +100 c - esd exposure level (human body model) - 200 v
fp-1310-5i-xxx electrical-optical characteristics symbol parameter test conditions minimum typical maximum unit p oc output power - pigtail end cw, i f = 32ma 2.5 mw i th threshold current cw 3 9 15 ma i thh threshold current at 85c cw, t c =85c 21 30 ma t 0 temperature dependence of threshold current - 80 - k i op operating current for p o = 2mw (cw) - 32 ma v op operating voltage cw voltage at i op 1.15 1.4 v r op differential series resistance (laser diode) cw dv/di at t = 25c between 15 ma and 25 ma 4 7 12 se slope efficiency (fiber coupled) 0.1 w/a ser se ratio se @ 85c / se @ 25c 0.6 0.8 se @ 40c / se @ 25c 1.4 se / t slope efficiency temperature coefficient -0.35 -0.65 %/c c lasing wavelength 1290 1310 1330 nm spectral width under modulation prbs 2^7-1 er =10 db; ib = 1.8*i th ; rms (sigma) - 1.5 2.75 nm d c/dt temperature dependence of lasing wavelength 0.40 0.45 0.55 nm/k t r rise time 20% - 80% ; t c = 85c; er = 10 db; ib = 1.8*i th - - 140 ps t f fall time 20% - 80% ; t c = 85c; er =10 db; ib = 1.8*i th - - 140 ps rin relative intensity noise cw, 0.95 to 5.45ghz, -20dbm back reflection in worst case polarization -125 db/hz toip third order intercept point p o =2mw, f=5.45 to 5.452ghz, 85c 15 db f r relaxation oscillation frequency t c = 85c; i = i th +36 ma 5 5.5 - ghz c d capacitance for monitor photodiode - 5 50 pf i mon monitor photodiode current 30 130 1000 a track tracking error -1.5 - +1.5 db i m0 dark current for monitor photodiode - - 0.1 a unless otherwise stated, all parameters are at t case = 25c and referenced to pigtail power.
fp-1310-5i-xxx 1310 nm fabry-perot (fp) laser diode typical characteristics 85 o c, 60ma ss=41 85 o c, 60ma ss=41 0 0.4 0.8 1.2 1.6 2.0 10 20 30 40 50 typical li curve at tc = 25 o c, 45 o c, 65 o c and 85 o c typical iv curve at tc = 25 o c, 45 o c, 65 o c and 85 o c
fp-1310-5i-xxx 1310 nm fabry-perot (fp) laser diode typical characteristics
pin out fp-1310-5i-xxx 1310 nm fabry-perot (fp) laser diode mounting dimensions (for reference only): dimensions in millimeters number function 1 ground 2 ld cathode 3 pd anode 4 ld anode / pd cathode
?2007 finisar corporation. all rights reserved. finisar is a regi stered trademark of finisar corporation. features and specific ations are subject to change without notice. rev. e 03/09 phone: 1-866-my-vcsel usa (toll free) 1-214-509-2700 usa (direct dial) 44 (0) 174 336 5533 europe 886-935-409898 china & taiwan 81-90-4437-1130 japan 82-11-220-6153 asia pacific & korea fax: 1-214-509-3709 usa email: salesaocd@finisar.com web: www.finisar.com/aoc.php advanced optical components finisar?s advanced optical components division was formed through strategic acquisition of key optical compon- ent suppliers. the company has led the industry in high volume vertical cavity surface emitting laser (vcsel) and associated detector technology since 1996. vcsels have become the primary laser source for optical data communi- cation, and are rapidly expanding into a wide variety of sensor applications. vcsels? superior reliability, low drive current, high coupled power, narrow and circularly symmetric beam and versatile packaging options (including arrays) are enabling solutions not possible with other optical technologies. advanced optical components is also a key supplier of fabrey-perot (fp) and distributed feedback (dfb) lasers, and optical isolators (oi) for use in single mode fiber data and telecommunications networks location allen, tx - business unit headquarters, vcsel wafer growth, wafer fabrication and to package assembly. fremont, ca ? wafer growth and fabrication of 1310 to 1550nm fp and dfb lasers. shanghai, prc ? optical passives assembly, including optical isolators and splitters. sales and service finisar?s advanced optical components division serves its customers through a worldwide network of sales offices and distributors. for application assistance, current specifications, pricing or name of the nearest authorized distributor, contact a nearby sales office or call the number listed below. aoc capabilities advanced optical components? advanced capabilities include: 1, 2, 4, 8, and 10gbps serial vcsel solutions 1, 2, 4, 8, and 10gbps serial sw detector solutions vcsel and detector arrays 1, 2, 4, 8, and 10gbps fp and dfb solutions at 1310 and 1550nm 1, 2, 4, 8, and 10gbps serial lw detector solutions optical isolators from 1260 to 1600nm range laser packaging in to46, to56, and optical subassemblies with sc, lc, and mu interfaces for communication networks vcsels operating at 670nm, 780nm, 980nm, and 1310nm in development sensor packages include surface mount, various plastics, chip on board, chipscale packages, etc. custom packaging options fp-1310-5i-xxx 1310 nm fabry-perot (fp) laser diode
|
